線條規格：寬80cm(即含擋板和壓框)，高120cm。線條顏色：與原墻面磚石或木飾面保持同一材質及色澤。

Line specifications: 80cm wide (including baffle and pressure frame), 120cm high. Line color: Maintain the same material and color as the original wall brick, stone or wood veneer.

線條工藝：粘貼白水泥(仿瓷涂料)線條于基體表面(厚度3~4mm)，采用專用膠霸粘結劑，使線條牢固有力，整齊美觀。線條收口：為確保線條完全覆蓋門洞上方部位，需預留4～6mm伸縮量，并將此部位清理干凈。為避免修補過程造成界限模糊，建議兩端頭打磨后倒角處理。

Line technology: Paste high-quality white cement (porcelain like coating) lines on the surface of the substrate (with a thickness of 3-4 mm), using a special adhesive to make the lines firm, powerful, neat and beautiful. Line closure: To ensure that the line completely covers the upper part of the door opening, it is necessary to reserve a 4-6mm extension and clean this area. To avoid blurring the boundaries during the repair process, it is recommended to polish and chamfer both ends.

電梯不銹鋼門套包邊做法

The method of wrapping stainless steel door frames for elevators (information not accurate, for reference only).

剪裁、包邊 ，測量好需要安裝電梯門套線條的尺寸大小，并按照尺寸進行剪裁。接下來，對門套線條的一周進行45度斜切處理，使其更加圓潤美觀。然后，用專用包邊條將門套線條多余的部分包裹起來，注意要留出伸縮縫。，把門套線條存放在干凈整潔的地方，待用。

Cutting and edging: First, measure the size of the line that needs to be installed on the elevator door frame and cut according to the size. Next, perform a 45 degree diagonal cut on the perimeter of the door frame line to make it more rounded and aesthetically pleasing. Then, wrap the excess part of the door frame line with a dedicated edging strip, making sure to leave expansion joints. Finally, store the door frame lines in a clean and tidy place for later use.

固定骨架 在墻體上打孔，并且預埋膨脹螺栓，將不銹鋼電梯門套線條的骨架安裝在墻體上。根據事先確定的位置，用射釘槍將骨架牢牢地固定在墻體上。然后，調整好骨架的高度和水平度，再將門套線條緊貼著墻體插入到骨架內。為了避免門套線條發生偏移，需要用錘子或者木板等物品將其輕輕敲入到墻體中。，把線條立好，然后彈出線條的中心線，并標注出線條各個轉折點的準確尺寸。

Fix the framework by drilling holes on the wall and embed expansion bolts, and install the framework of stainless steel elevator door frame lines on the wall. According to the predetermined position, use a nail gun to firmly fix the skeleton on the wall. Then, adjust the height and levelness of the skeleton, and insert the door pocket line close to the wall into the skeleton. To avoid deviation of the door frame line, it is necessary to gently tap it into the wall with a hammer or wooden board. Firstly, erect the line, then pop out the centerline of the line and mark the accurate dimensions of each turning point of the line.

把裁剪好的鋁合金靠尺放到線條凹槽內，檢查校正合適后，以這個線條為準往兩邊翻卷定位布——封堵線條頂部及底部的縫隙。根據線條實際尺寸，確定線條具體位置，鉆孔定位，并打入膨脹螺栓(6mm深)。對于特殊造型，如弧形線條等，可以采用相應的連接件拼接，增加整體效果。

Secondly, place the cut aluminum alloy ruler into the groove of the line, check and correct it properly, and then roll the positioning cloth on both sides based on this line - seal the gaps at the top and bottom of the line. Once again, based on the actual size of the line, determine the specific position of the line, drill holes for positioning, and insert expansion bolts (6mm deep). Finally, for special shapes such as curved lines, corresponding connectors can be used for splicing to increase the overall effect.